Version 15 (modified by morphis, 7 years ago) (diff)

Some updates ...

Disclaimer (WebOSInternals' credit)

Enacting any set of instructions from this site has the (remote, but greater than zero) potential to void your warranty. Our intention and the specific design of all instructions is such that you should be able to recover using the webOS Doctor should anything go wrong, and put your device back to a state which is indistinguishable from a factory-new device, but we give no guarantee. Use any information from this site at your own risk. At the very least, you should be prepared to lose all data on your phone at any time. We cannot tell you what you should do - we provide the information, but it's up to your own sense of personal responsibility to determine what you do with that information. We require you to use the webOS Doctor to put your device back to factory condition before contacting Palm or your cellular carrier for service or support.

Please report any issue to shr-devel attt with subject "PalmPreInstall" to help us in our project. Thanks

Installation and Usage of SHR on the Palm Pre

What to expect

This howto will help you how to install a recent SHR image on the Palm Pre/Pre2 device. We try to not lose your data from WebOS which can be installed in parallel, but don't be surprised if not! Don't expect a usable phone after you installed SHR too! You have been warned. That said, currently the installation is quite safe. Your device is backed up before doing anything, so you should be able to restore your data later. See Status section to see what progress has been made


Needed things

  • a computer with linux installed
  • an active internet connection
  • Palm Pre device attached over USB to your compuer
  • the webos doctor corresponding to your device (see WebOS Internals' wiki)
  • novacom, and just novacom! (<= This for the pre only. For the pre2 they have not yet published an updated version of novacom. Come to our irc channel and we will see what we can do)

Step one

Create a "downloads" directory and put in there the webos version you have downloaded, something like webosxxxxx.jar .

Step two

In our working directory (not in "downloads/" !), download the fso-installer (a Makefile;a=blob_plain;f=palmpre/fso-installer/Makefile;hb=HEAD )

Step three

You have then to modify only two things in the Makefile : TARGET and CONFIG_WEBOS_MEDIA_TARGET_SIZE as explained at the top of the Makefile

So for now you have something like this :


Step four

Plug your device to your computer with the usb cable.

Step five

Put your device in developer mode.(see WebOS Internals' wiki)

Step six

Open a terminal in your working directory an launch the installation with

make install-all

Step seven

It is time to go grab something/someone to eat/drink or kiss because from now your computer will follow the Makefile and making through all the needed things to install FSO/SHR on your precious!

How to switch OS

We use the bootr ( bootloader to switch between webOS and SHR. See this video to get an idea about bootr works.

How to update all your FSO/SHR

Now you want to update your FSO/SHR version, good!

There are two solutions!

The first one is just to update it directly from FSO/SHR

opkg update
opkg upgrade

The second one is more heavy stuff

WARNING: it will remove everything of your FSO/SHR partition

Step one

Plug your device to your computer with the usb cable and put it in recover mode.(see WebOS Internals' wiki)

Step two

make update-all

Step three

make reboot

NOTE: If you want to update just your kernel or your rootfs you have then an other step for example:

make memload
make update-kernel
make reboot

That is all for tonight! Question Do we put here target by target description?


WARNING! It is still really experimental for the moment! only not for beginners.

We now have a dual-boot solution, Bootr! See this video

SHR on pre's device still does not offer much than just standards applications working.. no gsm?

a link to what FSO supports ?